If I recall the 855d has the same chassis as my 825i, I went all the way up to CST Clincher 27x9-12 and 27X11-12 on my original rims. The CST also had a much higher load rating.
Big Horns are ok,...
Type: Posts; User: scoobieguy
If I recall the 855d has the same chassis as my 825i, I went all the way up to CST Clincher 27x9-12 and 27X11-12 on my original rims. The CST also had a much higher load rating.
Big Horns are ok,...
You want something low profile to prevent taking out / breaking or forcing your door to open when you lest expect it.
Got to watch out for Gator hijackers :-) Or the wife and kids wanting to use...
1- The weld on hinges have held on even with the top part on, no issues at all. My guess for the each full doors the weight must 80 pounds, half would be 35 pounds. We did a long ride 50miles of...
Alternator and Starter Supplier US and Canada
--------------------------------------------------------------------------------
I found an good supplier for alternators and starters. The prices...
Top of doors added, now have the full cab.
Not completely air tight, but much better in cold weather. Would just need to add door molding, however that would mean fogging up without a dedicated...
Glenn 1 year later do you have any problems with CV joints / axles with the 2in lift on your 825i S4?
Did john deere give you grief for service / warranty claims?
I'm considering the same setup ...
After an 80km ride in rough terrain I checked for loose components, and I found the radiator to be very loose, rattling around approx. 1/4 inch. I don't think that is normal, a car radiator doesn't...
Here is my homemade rear bumper for a gator 825is4
I didn't want to spend $300 on the JD rear bumper so I made my own for less than $50.
I still purchased the side fender guards because I didn’t...
Here are my homemade half doors for a gator 825is4, I will build the top part for the winter to have a full cab.
Over the past 3 months I guess it took me 50 plus hours to build.
A long time but...
Good point Dane, fling to China to save $20 is not cost effective.
However I did fin that Joyner US makers of the sand viper buggies uses chery engines, ...
I wonder if the no start problem would be related to a bad neutral switch, I remember if you leave the machine in gear you cannot start it, must be in N.
Could still be a bad ground / connection elsewhere along the line.
Check out this post https://www.gatorforums.net/forum/gator-lighting-stereo-electrical/958-engine-will-not-crank.html
If I take a...
Product Name:COOLING DEVICE 372FDJ-LQZZ
Поз. Номер Наиминование
1 Q1400612
BOLT - HEXAGON HEAD
2 372-1307014
PULLEY - WATER PUMP
3 Q1840840
BOLT - HEXAGON FLANGE
4 Q1840855
Product Name:VALVE CHAMBER COVER 372FDJ-QMSZG
1 372-1003090
COVER-OIL TANK CAP
2 Q2540616
BOLT
3 372QMSZG-ZSZ
ENGIEN TRIM COVER ASSY
4-1 372-1003030FA
COVER ASSY - ROCKER
4-2...
Powering the 825i is a liquid-cooled, 812cc, EFI, DOHC, Inline Triple,
The engine is from a mini car manufactured by Chery International in China the Chery QQ 0.8 engine model 372
I put together...
https://www.johndeeregatorforum.com/forum/showthread.php?12377-550-Roof-Lights-Installation
These 2 posts show ho you can fish wires from the bottom of roll cage to the top using factory holes
...
Don't laugh too hard at the smell test :BG: but here goes ...My guess would be oil from an oil and filter change burning off typical blue smoke and burnt oil smell.. Check if the oil filter has a...
Yes gators are not submarines but the placement of the air intake is really poorly designed.
If you suck in any amount of water you will have a very expensive repair bill, and the amount of dust...
Check out allied electronics they carry a wide range of Eaton Euro rocker switches that are an exact fit in the cutouts of JD, these are $5 to 10$les then JD ones....