Has anyone been able to locate aftermarket Ball Joints for a 2011 825I? (As best i can tell they are AM137741 and AM138400). I have tried cross reference on Napa with no luck.
Thank,
David
Type: Posts; User: Dlauffenburger
Has anyone been able to locate aftermarket Ball Joints for a 2011 825I? (As best i can tell they are AM137741 and AM138400). I have tried cross reference on Napa with no luck.
Thank,
David
I know this has been discussed previously but i have spent about an hour searching and cannot find it.
Has anyone found a descent set of CV Boot pliers that work on the Oeticker Low Profile clamps...
Anybody ever get an answer on which ground lug needs to be relocated?
My gator starts up fine in the morning or after it has been sitting for a while (1-2 hours) but if you run it for 5 minutes or longer it will crank for 10 to 15 seconds before it will start. After...
Thanks for the reply and link. The remote looks nice, but more than I want to spend right now. I will tear apart the current control switch and find a substitute for the wire.
Thanks again.
I have the Warn winch on my 825I and the Remote Control wire is a stiff flat black (similar to old TV Cable) wire that is a PIA to use. Has anyone changed it out for a more useable wire? If so what...
Where are the pictures? Without pictures, it never happened :lol:!!
I concur with Duling, if I shift into gear with the RPMs above 1100 I get a clank in the tranny. Try letting the engine idle down below 1100 rpms before shifting and your clank will probably...
The RPOS has changed quit a bit, i purchase a Roof and enclosure for my 2011 in the fall and they sent me 2013 items, neither one fit. From what i could tell the shape of the rear section has...
RMOSS01,
Thanks for the reply. After growing up on a farm and 28 years in the Navy I am somewhat obsessed with ensuring maintenance is performed and a Zerk fitting just screams for grease. I...
I have a 2011 825I with the 14 Zerks for greasing the suspension. I have greased the suspension twice now and each Zerk only takes about 1/8th of a pump before grease starts to squirt out from right...
I just installed some new lights on my machine and was a little worried about the 15Amp circuit so I hooked my lights into the 40Amp circuit with an inline fuse for the lights. there is a empty...
I have a 2011 825I and as soon as it got cold outside (below 40F) I started to hear a lot of strange noises from under the gator, it sounds like it starts under my feet and goes to the rear. I...
Interesting, if the Generac filter has the same bypass valve pressure setting I would be inclined to use one. Extra filtering is always a good thing especially on an engine that has such a small oil...
Any pictures and data on the plow?
How did it work?
I want to Thank everyone for the advise. I found the Rigid Dually Floods and sale and bought them, they are everything they are said to be. High quality construction and very bright.
Thanks...
I'll ask the dumb question, what did you use to get the fluid into the front differential :Cnfsd:? I can't believe the design they used for the fill port :Bnghd:, how expensive would it have been to...
Mine does the same thing. The only thing I can figure out is that when I first start it in the morning the engine starts at approximately 1600 RPM for the first couple of seconds and the primary...
Jradue,
Did you get your new lights installed yet? If so, what is your impression.
Dave
I am going to purchase a Soft Door and Rear Window combo. USA UTV and All Terrain Online both over the combos, has anyone bought either of these enclosures? If so can tell me if you liked it and...
After I read Jradue's email I went on Amazon to look at the Tuff lights as well. I saw the square lights for $60 and then the Oval lights for $97 which I liked better because of the specs, but after...
Jradue,
did you order the 4" square lights or the 5" ovals? It looks like the oval version costs a little more but puts our more lumens.
Dane,
Thanks for the measurement! Did you buy yours local or did you find a better price online?
Dane, Thanks for the reply. I am referring to the Rigid Dually's you recommended, the roof on my 825I is quite a bit different than yours; it has a large pocket in the front that is supposed to...
Has anyone tried to mount the Rigid Industries lights in the recessed area of the Ploy Roof? I know they will fit within the width but am curious if they fit in the depth of the recess. ...