I wouldn't give it a second thought. I added a heavy duty bed mat that weighs aprox. 70 lbs with no discernible difference in power/acceleration, granted I only have the two seater.
Other thing to...
Type: Posts; User: g8erh8er
I wouldn't give it a second thought. I added a heavy duty bed mat that weighs aprox. 70 lbs with no discernible difference in power/acceleration, granted I only have the two seater.
Other thing to...
Might wanna check their ratcheting grip too - would think they'd hold the poles more secure as opposed to the static grip version posted earlier.
...
I'm not sure what you need jack stands for? If you're using a floor jack, simply place under the rear reciever hitch. It's quite stable that way. I use this method when I need to lift the rears off...
Just wanted to say thanks once again for the write up Bunky. I followed yours to a tee and everything went smoothly. Only difference is that I followed your advice and did the quick disconnect for...
Found it - sandwiched in between some other wires so you could only see it from underneath. Thanks Bunky.
Weird. I do have power steering, not sure if that would use it or not. The yellow wire in the pic is part of the flasher harness. I'll have to take a closer look this weekend. Might be buried behind...
Having trouble locating the yellow/black connector from the main harness. Here's what mine looks like.
2866
I do have the red/black connector - my flasher kit is plugged into it and there's an...
These must be the new poly doors I posted about a while back. Only the olive green were listed in the parts fiches at the time and no full kit # was available. Wonder if they'll be $500 when...
Bunky, that garage looks waaay too organized. Join the rest of America and junk it up a bit! :BG:
Don't mind me. Just envious since our single car garage is busting at the seams.
Good to know Bunky. So it looks like it's luck of the draw as to whether you get the updated version. Best to use a supplier with new stock.
See below - this is the angle of the mirrors at the extent of their vertical adjustment. The mounting plate is different from the one pictured - not nearly as much vertical adjustment.
2827
I...
Strange, I found the 65mm cap to be too small for the first oil change. I bought the 65/67mm cap from Advanced Auto and the 67mm end was the one that fit the factory filter.
Bunky - same model number I purchased. Problem is, they just aren't adjustable enough. You'll see if you get them. If the mirrors themselves had more up/down adjustment at the ball joint, it wouldn't...
Thanks Bunky. There's actually 18 or so different flash patterns for that particular strobe. If I wanted, I could add a momentary rocker to the switch bank that allows you to cycle through the...
Installed everything last night and took longer than expected because I mounted the switch bank to the rear OPS bar and ran wiring through the tubing. The passenger side bar has no access hole to the...
I have them Bunky - purchased from an eBay seller for around $52 shipped. The comments reg. looking at the rear tire are correct. You have to mount them quite high to see anything. Here's a pic of...
From what I can see in the parts fiche (someone please correct me if I'm wrong) it looks like the harness used for spots on the brush guard is AM137558. The harness uses one relay (PN AT75769), and...
Anyone have the correct part number for the JD filter cap?
Bunky, I don't think the OP is referring to those. He's interested in the bumper cover light kit (BM24090). At least that's what I think since he typed "the lights installed in the bumper".
EDIT -...
OK - think I have it figured out. The yellow wire is used to change the flash pattern on the strobe. You hold it to 12+ for just a second and it alternates to the next pattern. The momentary switch...
Thanks emnesto - that's exactly how I thought it should be wired, but I can't wrap my head around the fact that the strobe will be hooked directly to the pos/neg of the OPS harness, which would...
I just received the OPS switch bank and an emergency strobe light that I will be attaching to the poly roof.
I'm confused as to how to wire the strobe into the OPS switch bank. Below is the wiring...
Bunky - one suggestion. I noticed this was posted in the Gator Showroom forum but not in the actual 825i forum. You may want to post it there as well so the 825i guys don't miss it. I only saw it...
I have a copy of the instructions Bunky. It basically just tells you into which empty connectors the supplied harness plugs into. Nothing about adding a parking light function.
For parking lights,...
Wow Bunky, excellent write up and detailed pics. This will surely help anyone planning on going this route, myself included. Thanks for taking the time to post!!