PDA

View Full Version : 825i driveshaft replace



Thomas
02-19-2012, 07:54 AM
Guys - for those of us not as close to this issue - what vintage machines would you recommend calling the dealer on this issue? My gator was purchased July of 2011 - and not sure if I should be proactive and call the dealer on this one or not. Thanks!

Deputy347k9
02-19-2012, 08:22 AM
Thomas, according to other Forum members, John Deere published "solution 87518 during October of 2011. However, I am not sure as to when or even if they have installed the upgraded pillow block bearing witht the rubber isolator into the new Gators?

As you I would be interested in knowing WHEN they started to install the new style bearing?


Larry from ME

duling
02-21-2012, 07:38 AM
I purchased my 825i in July 2011 as well and I just recently had mine repaired. It made a huge difference!

jandrold
02-21-2012, 07:47 AM
Do they look diffrent an if so is there a picture of the new one out there?

Jim O.
USMC Ret.

Deputy347k9
02-21-2012, 07:49 AM
Would have been much easier if John Deere said this soluton effects all those machine built prior to, or machines will serial numbers before. However if they had done that then this would have been a recall I believe. Does John Deere actually use a "recall"?

Larry from ME

Thomas
02-21-2012, 07:50 AM
Follow-up on this - I contacted the dealer I purchased my gator from. He got me in touch with the service department to schedule the fix.....

plateauman57
02-21-2012, 10:53 AM
does anyone know if this issue is confined to the 2011s? mine is a 2012 and was just wondering if i should contact my dealer. haven't noticed any issue/problem yet but would not want to wait if no need.

Deputy347k9
02-21-2012, 01:05 PM
Hoping a John Deere Tech will chime in here and let us know, if known, what machines have the problems? Like all machines built before this date or serial number? I would imagine Johne Deere has changed the bearing in newer machines, at least I hope so?

Larry from ME:hdscrh:

Regulator
02-22-2012, 09:14 AM
does anyone know if this issue is confined to the 2011s? mine is a 2012 and was just wondering if i should contact my dealer. haven't noticed any issue/problem yet but would not want to wait if no need.

I bought my 2011 825i in late September and when it was in the dealersjp for some work a few weeks ago, my service guy said mine already had the updated driveshaft, so I am guessing that it was limited to machines built prior to September of 2011....I could be wrong on this but since he said mine was good to go, it was fixed at the factory or by the dealership before they sold it to me....

Larry in MD :Jestr:

GATORDONE
02-22-2012, 09:58 AM
There has been issues with the driveshafts on earlier 620i and 850d models, Mostly alignment problems and lack of grease. Lot more issues with the 825i because of the increased H.P. and torque of the engine and also increased speed.There wasn't a serial number cut off point of the new rubber hanger bearing, But what like Larry said sometime after september.Should there be a pip? YES!

CaptDan
02-22-2012, 10:20 AM
Larry,

Maybe you could help us out and although you bought your machine in September of 2011, can you check and let us know when your machine was manufactured ?

Thanks

Dan


http://i1080.photobucket.com/albums/j336/CaptDan/gatorserialnumber.jpg
<a href="http://s1080.photobucket.com/albums/j336/CaptDan/?action=view&amp;current=gatorserialnumber.jpg" target="_blank"><img src="http://i1080.photobucket.com/albums/j336/CaptDan/gatorserialnumber.jpg" border="0" alt="Photobucket"></a>

825joe
02-22-2012, 10:52 AM
I had mine done last week or so. Made a world of difference. It is much smoother and feels a lot better. I told my dealer about some vibration and they took care of it with the new driveshaft. Very happy.:Thmup:

ps. I purchased mine Feb 25th 2011

LeonardS
02-22-2012, 11:48 AM
My 825i was built in May 2011 and I picked it up in June. I contacted my JD Dealership yesterday and am taking the Gator to them on Friday. They are going to replace my driveshaft.

Leonard

pahawi
02-22-2012, 12:07 PM
Little confused here - some mention the drive shaft being a problem too. Does solution# 87518 from October of 2011, include a new drive shaft too, or......?

Thanks.

Paul

825joe
02-22-2012, 12:48 PM
yes the whole front drive shaft is replaced. It comes with the new ruber mount.

Regulator
02-22-2012, 08:53 PM
Larry,

Maybe you could help us out and although you bought your machine in September of 2011, can you check and let us know when your machine was manufactured ?

Thanks

Dan


http://i1080.photobucket.com/albums/j336/CaptDan/gatorserialnumber.jpg
<a href="http://s1080.photobucket.com/albums/j336/CaptDan/?action=view&current=gatorserialnumber.jpg" target="_blank"><img src="http://i1080.photobucket.com/albums/j336/CaptDan/gatorserialnumber.jpg" border="0" alt="Photobucket"></a>

Dan...I will do that....unfortunately, my Gator is still in my Trucking Company Shop, so I will check tomorrow when I go into work....where is that VIN/PIN tag???...I am sure I've seen it before, but don't remember it off-hand right now....

I'll let you all know something tomorrow evening....

Larry in MD :Jestr:

825joe
02-23-2012, 09:10 AM
it is on the frame on the passenger side in front of rear wheel.

Regulator
02-23-2012, 10:28 AM
it is on the frame on the passenger side in front of rear wheel.

Thanx Joe...I saw it somewhere but couldn't think where it was without the Gator sitting in front of me...hahaha....I will check it out and report what the date of manufacture is...

Larry in MD :Jestr:

825joe
02-23-2012, 10:56 AM
Thanx Joe...I saw it somewhere but couldn't think where it was without the Gator sitting in front of me...hahaha....I will check it out and report what the date of manufacture is...

Larry in MD :Jestr:

no problemo Larry:Thmup:

Regulator
02-23-2012, 08:16 PM
My Gator was built on March 12, 2011 according to my sticker on the frame...that's about 3 weeks before yours was built Dan....did yours have the updated driveshaft or did you have to get the dealership to do it later???....I asked my Service Manager and he said that I was good to go, but now I'm wondering about that...I don't think mine is vibrating or anything like that...I have 225 miles on it, with around 25 hours, I think....if you had to get yours fixed Dan, then I'm gonna check to see if mine was really done, or if maybe the dealership did it before I bought it....I don't want anything to happen to it later on and wish that I had pushed the dealership to tell me what was done to it...maybe I am worrying for nothing...I hope so!!!

Larry in MD :Jestr:

CaptDan
02-23-2012, 08:23 PM
My Gator was built on March 12, 2011 according to my sticker on the frame...that's about 3 weeks before yours was built Dan....did yours have the updated driveshaft or did you have to get the dealership to do it later???....I asked my Service Manager and he said that I was good to go, but now I'm wondering about that...I don't think mine is vibrating or anything like that...I have 225 miles on it, with around 25 hours, I think....if you had to get yours fixed Dan, then I'm gonna check to see if mine was really done, or if maybe the dealership did it before I bought it....I don't want anything to happen to it later on and wish that I had pushed the dealership to tell me what was done to it...maybe I am worrying for nothing...I hope so!!!

Larry in MD :Jestr:

I have not had mine done yet. I just figured any noise I heard was normal Gator noise to be honest. I have about 71.3 hours and and 478 miles on mine. The biggest complaint I have is that the bed squeaks so much, it's annoying to be honest. End of March I will be back out in Pa near where I bought it, I am going to ask them when they service it to look at the drive shaft and see if mine needs to be or should be replaced. I'll keep you posted.

Dan

plateauman57
02-23-2012, 08:26 PM
Not sure when in 2011 my unit was built but it's a 2012 model, according to the certificate of origin. I bought it december 30th, 2011. I asked my dealer about it today and he was unaware there had been a problem so he called the service manager and he said they had only replaced two, one was due to someone hitting a tree and breaking theirs. I'm not too comfortable that mine is good to go. Will have to keep an eye on it...and ear too.

Regulator
02-23-2012, 08:34 PM
Dan...thanks....I am glad that you haven't noticed anything wrong more than anything, which could mean that our Gators are already fixed...I am still going to check with my dealership to make sure whether or not it has the updated driveshaft OR if it's just the new style bearing as the fix...I want the correct driveshaft even if the new bearing patched it up....

Oh yeah, Dan...you are complaining that your "bed is squeaking too much"???....er...um...ahem....do you not know what is causing that???....I wish MY bed was doing more squeaking than it is!!!.....hahahaha!!!

Larry in MD :Jestr:

duling
02-27-2012, 08:01 AM
I fixed my squeaky 'gator bed' by putting a tiny bit of lithium grease on all the points that the bed contacted the frame including the latch and haven't had a squeak since.

To fix my squeaky 'marital bed' I had two kids... problem solved.

purplewg
02-28-2012, 10:02 AM
To fix my squeaky 'marital bed' I had two kids... problem solved.

Now that is just wrong, wrong, but true.:BG:

Deputy347k9
02-29-2012, 07:40 AM
duling

I would bet that fixing the squeak in the marital bed was far more expensive then repairing the Gator bed! lol. I agree with purplewg your not right!

Larry from ME:crzy: