PDA

View Full Version : ground clearance ?



Jack B
03-02-2012, 06:20 PM
Has anyone measured the ground clearance on a 825 or 855. Do you need the 27" Bighorns option to get the full 11"/12.25" stated on the JB web site?

Has anyone measured their actual turning radius?

CaptDan
03-02-2012, 07:47 PM
I have to say, not me, never even thought about it .

Dan

ps ...welcome to the forum. where in the world are ya from ?

Jack B
03-02-2012, 08:40 PM
Hi Dan, I live in CT, my land is very rocky with steep grades and thick woods. so ground clearance and turning radius are very important to me.

Regulator
03-03-2012, 12:33 PM
I'm not sure about the ground clearance thing, but I do know that the turning radius on there 825i's are pretty small....I ride down an old Fram lane a bunch in the field next to my house, and when I get to the main road, I can drive out of the farm lane into the road while hugging the right side on the lane, and turn it hard in the road and drive right back into the lane without cutting any corners off....that's pretty good to me...

Please excuse my overly scientific explaination...luckily, I decided against using hand drawn geometric diagrams to back up my theory concerning diagonals, curves, gravitational G Forces, and how lunar phases figures into the equations using pi as a consonant....

Yeah right........

Ohhh...I wrote pi....now I'm hungry....

Larry in MD :Jestr:

ratrod
03-03-2012, 02:34 PM
You will gain the coolness factor of those sweet 14" aluminum wheels with the big horns but they are only an inch taller than the standard 26" tire for the gators. Your best bet would be adjust the suspension all the way up, and go slow over obstacles.

My gator sitting on a concrete floor with the 26" tires measures 11" of ground clearance in the back with no weight.



Please excuse my overly scientific explaination...luckily, I decided against using hand drawn geometric diagrams to back up my theory concerning diagonals, curves, gravitational G Forces, and how lunar phases figures into the equations using pi as a consonant....


:Eek:

Jack B
03-03-2012, 05:16 PM
thanks for measuring. are the aluminum rims worth $799 for a 1/2 inch of ground clearance and some kool factor? maybe :)

jandrold
03-04-2012, 01:32 PM
Mine on the Big Horns measures 10.5 frt and 11 rear and that is with the poly cab installed on it.

Jim O.
USMC Ret.

Jack B
03-04-2012, 04:16 PM
thanks Jom O, sounds like you would need to stiffen the shocks to get back some ride height? How do you like the poly cab? I am still trying to decide poly or Deluxe. I bet the deluxe would bring down the ride height even more?

jandrold
03-04-2012, 07:28 PM
I have the front shocks on the stiffest setting and the rear in the middle. I do not like the Poly cab at all but since it is paid for and on, it will do, I don't like the way the door opens and often comes unlatched when riding. Have adjusted them many times. You do stay dry setting still in a rain storm but I can see getting alittle wet if moving

Jim O.
USMC Ret.

Kiwi06
03-06-2012, 01:55 PM
Has anyone measured the ground clearance on a 825 or 855. Do you need the 27" Bighorns option to get the full 11"/12.25" stated on the JB web site?

Has anyone measured their actual turning radius?

Thought I had posted before, but I guess I never hit "Post". :hdscrh: Anyway...

I had been wondering about turning radius as that was one of my main concerns, and why I was considering the smaller machines. I ended up getting an 825i (last week :Thmup:), and your post prompted me to check. I made several circles in muddy sod and then went out an measured. Diameter of the outside of the tire tracks was a disappointing 326" (163" radius vs John Deere's spec of 148"). Still burning in my mind was other direction, so I tried that this morning. Ground was dry, so no new tracks, but I averaged a good foot inside the original track. I might have had a little slippage on the soggy ground, but not a foot! I guess I need to check steering stops. BTW, I have the 26" Ankla tires.

I will try to look at ground clearance to give another data point on that.

- Steve from ever changing CO (warm the last 3 days, snow expected tomorrow - always fun!)

Kiwi06
03-07-2012, 02:00 AM
OK, measured ground clearance on the concrete floor. With the 26" tires and set up as I got it from the dealer (low hour demo - I recall the springs are on lowest preload setting, but I'm not sure): 11.5 in front and 10.5 in rear. Protection package all the way around is the only significant added weight.

- Steve in CO

campoman
09-24-2018, 01:17 PM
has anyone looked at a way to increase chassis ground clearance the front is good but the rear by the receiver tube is to low to the ground ,the only way I can see to increase this is larger diameter tires, but by doing that im afraid I will loose low end power by changing final gear ratio, I believe that Big Horn makes a 28 inch tire to replace the 27 this would probably help but again im concerned about ratio change , has anyone tried this?

campoman
10-31-2018, 02:35 PM
yes if you want that full ground clearance , they also make a 28 inch Big horn from what I understand im not really concerned with the ground clearance on the front I dont like the ground clearance on the rear which iis considerably less , don'tknow if any one has come up with a kit to raise the rear clearance ,haven't seen anything yet the only other way is to go to larger tire diameter but don't know how much this will effect gear ratio , don't think one size bigger would effect much but haven't tried it still have a lot of tread left on the 27 inch that are on it, I haven't actually measured the turning radius but I know it is about half of my 4x4 toyota pickup.