PDA

View Full Version : Chery Engine



dale5387
03-05-2012, 07:42 PM
I am in the market for a side x side & Gator 825i is on my list as well as the Ranger XP and Honda Big Red. Can anyone tell me about the history of the Chery engine used in the 825i? Also is the cab noise loud?

CaptDan
03-05-2012, 09:21 PM
Welcome aboard Dale,

I have the 825i with about 500 miles and 90 engine hours. So far no issues with the engine. I can't really say about the noise because to me it is not noisy at all, but after years of riding a harley and spending lots of time at the weapons range my kids tell me i am getting a little hard at hearing, that i turn the TV up loud. So someone else will have to tell you about the engine noise, I don;t hear any. Again I am very happy with the engine so far, no issues.

Good luck with your decision and keep us posted what you decide.


Dan

Kiwi06
03-05-2012, 11:51 PM
I have only a few miles on my 825i. It's open cab (with poly roof/windshield), so I'm not sure how valid my noise assessment will be. I got it before the weekend, but I had classes over the weekend and haven't gotten to play with it as much as I'd hoped. I haven't much to compare it to as far as side by sides go. It's quite a bit quieter than the 850D that I have used to haul stuff and spread at a friend's place. (Also have some time in a Kubota diesel - I recall that being louder than the 850D, but it's been a while. No experience at all with either the Ranger XP or Big Red.) Another friend commented that it was "so quiet" when she first got in. (I think her frame of reference is her brand new riding mower.) Not sure if she changed her mind when we took off. I wouldn't have noticed how loud it was as speed (only about 10-12mph) except for her comment at the start. It wasn't obnoxious, but I did notice that we were almost yelling to talk to one another. (I've only been up to a bit more than 15, so far, but I didn't notice it being noisy on that run. Most of the noise seems to be transmission, so the cab (or even rear enclosure) might help. FYI, MY reference points are my (open cab) tractor (usually wear hearing protection) and dirt bikes/3-wheeler (always have a well padded helmet squeezing my ears). I do plan on looking into sound mitigation at some point, but it's not a high priority.

As for the Chery engine, I don't really know much history other than it's an automotive engine and Chery itself has been in business for a while. Check other forums here, and search the web for more info, but I figure if John Deere is willing to back it, I am satisfied.

- Steve in hot/cold CO

Deputy347k9
03-06-2012, 07:51 AM
Welcome to the Forum and best of wishes in your upcoming purchase. Like you I was torn between several machines when I purchased my 825i. My decision to purchase the 825i was based on several factors. John Deere reputation, the 3 cyl vehicle engine displayed great response and ample power for any job that I could offer. I also thought the 825i had more area for farm use, such as the bed as well as the load this machine can handle. Over the past three decades I have had three wheelers, four wheelers as well as one other Gator. Nothing that I have owned compares to this machine. I have owned my 825i one year this month and have NEVER had one regret as to my purchase. Where this is a new line for John Deere I do now have the extended warranty. There are many options for the 825i covering about every use you could imagine.

One other important note is related to this Forum! The many owners of these machine cover many different backgrounds which is very helpful when deciding what to do. If ever a problem you will not find a better place to obtain help.

Again, best of wishes and please keep us updated regardless of the road you take.

Larry from ME

dale5387
03-06-2012, 09:32 PM
Thanks Guys for the info. Does anyone know of these units being used for commercial use, that is the true test.

2255puller
03-06-2012, 10:36 PM
I think that "farm use" is harder on equipment than "comercial" just my opinion.

Sunbelt, United Rentals, etc., have been renting gators for years.
I own a TX, HPX, 850D and the 825i. 825i is my favorite by far.

Thomas
03-10-2012, 07:41 AM
It could be easy to be concerned about the Chery engine. I am not - and here is why:
- The engine is used in cars - from China to Argentina. If you have been in any of these countries - you'd gain level of comfort. It is like a non-stop go-kart race and cars get USED
- Deere's quality system. All suppliers are screened and developed until hitting the Deere quality system.

Bottom line - a 175 year old company is not going to risk its reputation by sourcing a poor quality engine. Purchase with confidence and knowing the company will stand behind you - I did and they have!

Regulator
03-10-2012, 09:55 AM
Thomas...that's a great answer to a tough question...Thanx for posting it up!!!...I'm gonna use the part about it being used it cars from China to Argentina the next time the question is asked of me...

Your "bottom line" about a "175 year old company risking it's reputation", along with "them screening suppliers beforehand" are sort of what I have been using as my answer to the question of a Chery engine already...you just put everything together alot more eloquently than I have been able to do when asked...

Thanx for your input....:Thmup:

Larry in MD :Jestr:

Thomas
03-10-2012, 01:27 PM
My pleasure Larry....it's a big investment and your concerns are logical. Good luck!

Regulator
03-10-2012, 05:50 PM
I am totally tickled pink with my 825i!!!....I am a big promoter of these JD Gators to everyone that I think would be interested in one and I get that question alot about the gas engine in them...seems like no-one has a problem with a Japanese Kawasaki engine in a lawn mower, but when you tell them that the engine in the Gator is a Chinese Chery engine, they look at you like you've got an extra eye in the middle of your forehead sometimes...giving those folks a reason not to worry about these engines has always been a bit of a struggle for me....the way you've explained it will make it easier to let them know that they shouldn't have anything to worry about with the Chery engine...to be honest, I never heard of a Chery engine before I started researching these new Gators back before I bought mine...never knew they even existed...

again...thanx for making it easier to explain about the Chery engine...I'm gonna use your words pretty much verbatim...

Larry in MD :Jestr:

trackerkelpie
03-23-2012, 03:04 AM
Bottom line - a 175 year old company is not going to risk its reputation by sourcing a poor quality engine. Purchase with confidence and knowing the company will stand behind you - I did and they have!

Unfortunately, that 175 year old company, of whose tractors I am a great admirer, has put its name to some of the poorest quality, most badly designed lawn mowers. The "real JD engineers" who designed the brilliant 30 series tractors in general and the IVT transmission in particular, must be rolling their eyes at some of the other equipment getting away with wearing the green and yellow colors along with the deere badge.
To the original poster,do your own homework and make sure the vehicle measures up to the work you expect from it.

Deputy347k9
03-23-2012, 07:39 AM
I have owned John Deere equipment for at leat 40 years, my father before me owned the same for 40 years. We have really had some work horses over time with no regrets. However, I do understand what you talking about when it comes to lawn mowers. I believe it's "Lowe's" that sells a inexpensive John Deere riding lawn mower. This is a poor example of John Deere enginering, so bad that local John Deere dealerships will not do any type of warranty work on them. You have a problem then take it to Lowe's.

I own a John Deere X740 lawn mower and have no regrets what so ever. My father taught me young, "son you get what you pay for", how true this is.

I really don't think it was a wise decision for John Deere to offer out side vendors a cheaper version of their quality products, not good for the name.

Larry in ME

Regulator
03-23-2012, 10:22 AM
"I really don't think it was a wise decision for John Deere to offer out side vendors a cheaper version of their quality products, not good for the name."

I agree wholeheartedly Larry....that's a move that will hurt their reputation in the long run...those who bought the cheap "Lowes" mowers will usually not buy one of the John Deere "proper" bigger mowers when they decide to upgrade, fearing they will get the same quality machine...(or "lack of" quality...)

I LOVE my X540 Garden Tractor and it, along with the 5 or 6 other JD's that I've owned over the years have always treated me VERY well!!!...and, I will continue to buy more of them every couple years or so...

Larry in MD :Jestr:

Thomas
03-24-2012, 05:21 AM
Sorry guys - I disagree. When you talk about the Lowe's mower - what is your comparison? An x700.....or a MTD produced $1,000 competitor? This product is intended to compete against other $1,000 entry level competitors from Lowes, Home Depot and Sears. You are not going to get X300 / X500 / X700 level robustness out of the Lowe's model entry level $1,000 machine. Those are unreasonable expectations and not the design criteria.

IF you are comparing the Lowes product to it's competitors, you will find a product that is much better designed, more durable and longer lasting.

trackerkelpie
03-24-2012, 06:56 AM
Sorry guys - I disagree. When you talk about the Lowe's mower - what is your comparison? An x700.....or a MTD produced $1,000 competitor? This product is intended to compete against other $1,000 entry level competitors from Lowes, Home Depot and Sears. You are not going to get X300 / X500 / X700 level robustness out of the Lowe's model entry level $1,000 machine. Those are unreasonable expectations and not the design criteria.


IF you are comparing the Lowes product to it's competitors, you will find a product that is much better designed, more durable and longer lasting.

Deere's quality system. All suppliers are screened and developed until hitting the Deere quality system.


The question here is just where is the bar set now for the Deere quality. Is it where it is indicated by their tractors, even the low price point machines exude quality over their competitors, or is it at the bottom with their mowers? Here in Australia the same dealership parks a horrifically designed and produced green and yellow mower beside a 6430 Premium with the obvious insinuation that you can trust the mower on the strength of the tractor. Just ask the staff mechanics about the build and design quality of the former. The low end mower is no better, and probably no worse, than the competitor at the same price point but my point is that this whole addition of low quality products has diluted the John Deere brand so Caveat emptor.

Regulator
03-24-2012, 10:41 AM
Thomas...I think you are confused with the point we are trying to make....we aren't comparing those entry level machines at all...the Deere might well be better than the rest...my point, as well as Larry in ME's (I think..) was that Deere shouldn't have even started selling these low cost models to begin with...simple as that...if they are gonna make a product that is cheaper than their high quality machines and not want to service them at their dealerships, then they are hurting their reputation to a certain extent...

I hope that clears up what we were trying to get across....

Larry in MD :Jestr:

allenflucas
03-24-2012, 10:43 PM
I am having trouble with TP sensor on my gator, dealer put 1 all new assemly on it , and it was bad,, hope this is not something to look forward too.

Regulator
03-25-2012, 12:22 AM
I am having trouble with TP sensor on my gator, dealer put 1 all new assemly on it , and it was bad,, hope this is not something to look forward too.

You have an automatic Toilet Paper dispenser on your Gator???....I must have missed that option...dammitt...now I want one!!!....just gotta figure out where to put it....hmmm....:TT:

Seriously...(sorry for funnin' at your expense...)...I would hope this is a problem that is kinda rare, since this is the first I have ever heard of anyone having that happen...the really sad part is that I don't even have a clue what a TP sensor is....someone please clue me in...I'm sure after I see what it is, I will feel stupid for not thinking of it...D'oh!!!

Larry in MD :Jestr:

CaptDan
03-25-2012, 01:29 AM
Larry,

I'm with you ...... don't have a clue what a TP sensor is on the Gator. On my truck it' a tire pressure sensor, but I know the Gator tires do not have that !


Dan

Regulator
03-25-2012, 10:43 AM
Whew!!!...thanks Capt.....I thought I had totally lost my marbles not being able to figure out what the TP Sensor was...if it is something simple and obvious, at least there's 2 or us who are getting dody in our old age!!!...

I was thinking maybe "Transmission Pressure"....:Cnfsd:

Larry in MD :Jestr:

jandrold
03-25-2012, 10:47 AM
I know on my gator it stands for a Throttle Position sensor, All EFI engines have a Throttle Position sensor (TP sensor). It tells the computer how much throttle you are giving it and in turn it controls fuel flow.

Jim O.
USMC Ret.

Regulator
03-25-2012, 10:56 AM
Thanx Jim O.....there you go....something that I should have known...in fact, all of my Big Rigs have a Potentiometer that sits under the throttle pedal that sends a signal to the Lift/Fuel Pump that is basically the same thing....

And yes, I do feel dumb for not thinking of that...:Bnghd: :hsu:

Larry in MD :Jestr:

Kiwi06
03-25-2012, 01:41 PM
Thomas...I think you are confused with the point we are trying to make....we aren't comparing those entry level machines at all...the Deere might well be better than the rest...my point, as well as Larry in ME's (I think..) was that Deere shouldn't have even started selling these low cost models to begin with...simple as that...if they are gonna make a product that is cheaper than their high quality machines and not want to service them at their dealerships, then they are hurting their reputation to a certain extent...

I hope that clears up what we were trying to get across....

Larry in MD :Jestr:

In my mind, a better marketing strategy is how GE gets into the low end appliance market. Rather than risking the GE brand on entry level products, GE uses the Hot Point Brand. The Hot Point appliances often have the same components as the GE branded, but not always. I've bought Hot Point appliances when I needed to spend less, but I always knew that I was taking a chance on quality vs. the GE branded versions. There are two problem swith no "off brand". With "commodity"/entry level products, where price is most important, corners will be cut and the brand will take a hit (reputation). The second issue is that you are never quite sure where the "cheap line" stops and the "quality line" starts. It isn't always obvious based on price alone. (Perhaps this is why Green/Yellow is getting out of the low end mowers.)

My 2 cents (after inflation :BG:)

- Steve in CO

CaptDan
03-25-2012, 03:46 PM
I agree with Steve, the biggest problem is that it is not always obvious where the "cheap line" stops and the "quality line" starts.

Dan in NJ

Regulator
03-26-2012, 09:48 AM
I agree with Steve, the biggest problem is that it is not always obvious where the "cheap line" stops and the "quality line" starts.

Dan in NJ

I totally agree with that too and realize that the sad part of the statement is that it should never have come to the point where you HAVE to distinguish between the two...John Deere products with 175 years of quality backing them up should all be manufactured and sold with the same standards from the smallest nut, bolt, or fastener all the way up to their top of the line Combines, Excavators, and Mega-Tractors....

Anyway, that's how it should be in my eye's....:Thmup:

Larry in MD :Jestr:

jasonwaldner
04-14-2013, 10:30 PM
Sorry for butting in guys it seems like u know what ur talking about. So I've got a ? On 2011 825i. Is it Normal engine running hot. If chan?ged thermostat. water sensor. But still running hot. It seems like fan is coming on to late or somthing. or is it normal?. I don't know. Let me know. Thanks jjw

CaptDan
04-15-2013, 12:27 AM
Jason, welcome aboard. I have a 2011 825i also, I do not have a high heat problem, but I think some people have posted about it. Maybe you could do a search kn here. I also think I remember reading that the delay in the fan starting was due to a poor ground wire.

dale5387
04-15-2013, 07:32 AM
Running warm is not a bad thing. If your running below temp. the oil wil start sluding.

campoman
09-24-2018, 02:52 PM
from what I understand the Arizona and texas Border Patrol uses the Gator for patrolling the Border you might check with them on how they hold up.