kmjd44
03-05-2012, 09:42 PM
As I was researching power steering for the 825i, I was frustrated in the lack of real information on how to install, and the ultimate performance, of the system. Having just completed the install yesterday I thought I would post some observations and lessons learned. I also have done some evaluations of the system.
I'll start by saying I'm in the auto industry and I evaluate steering systems and other things regularly. I will also say I am not a mechanic and borderline incompetent electronically. If you are a good mechanic and understand wiring/soldering, etc. you are well ahead of me and this may be a fairly simple exercise for you to install.
1.) Ordered system on a Sunday and received it on a Thursday - very happy with the response.
2.) Professional grade looking system - everything you need to install (except tools)
3.) Installation manual was straight forward mechanically, but to an electrical novice like me was very vague in the wiring instructions. This caused me a lot of angst, and ultimately some rework
4.) I've seen others have installed this in 3 hours - it took me most of three weekend days, but I took my time, learned how to solder from the internet, made multiple trips to an auto parts store (and Home Depot). I also will say I took my time and enjoyed the journey - I didn't have a deadline so I didn't rush - don't need extra stress!
5.) You will find the disassembly of the steering wheel and dash easier than it looks. My gator has the optional heater so it took a little longer, but no big deal
6.) First challenge encountered was getting my hands down to reach u-joint at steering rack - not a lot of room and a little tough to see. I ultimately found a path for the ratchet with a couple of extensions through a hole in the frame from the left side of the machine
7.) Second challenge was the snap rings on the upper shaft just below the steering wheel - there is an upper snap ring and a lower snap ring and they are much thicker than most snap rings. I bought a Channel Lock snap ring wrench on Amazon.com and it worked great on the upper snap ring. I then spent roughly 90 minutes on the lower snap ring, breaking the tips of the wrench and ultimately giving up and grinding off the snap ring after I thought I'd spent enough time on it (I considered cutting the whole shaft off with my Sawzall but finally got off the snap ring!). Could not proceed until I got this snap ring off because you must slide the shaft up to remove.
8.) Positioning the power steering unit was a bit challenging but not too bad - everything lined well with the frame.
9.) Had to sand off the paint on the upper shaft of the new unit to make it fit through the exisiting bearings on the frame.
10.) Total pain to try to tighten up the lower u-joint at the steering rack. You have to manage to hold one end of the bolt and reach through the aforementioned hole in the frame with a ratchet with extensions to tighten - trust me this will test your patience
11.) Once the unit was in went through the learning curve of understanding where to tie in to the existing wiring. You need battery power, a clean ground and switched ignition power. I grabbed the battery power from what I think is the fan relay in the front right of the machine. Picked up the ground from a bolt on the frame. Picked up the switched ignition power from the YELLOW wire off the ignition switch. (My biggest lesson learned is to check the power of each of these points before ever diassembling the machine - I tried to do it from a schematic and it is MUCH easier with a multimeter).
PERFORMANCE EVALUATION
I bought this system because 1.) the Boss snow plow makes the steering efforts very high and 2.) I want my wife to be able to use the machine and snow plow if I am gone. I evaluated the system first with the plow off, then with the plow on.
I am mostly happy with the system - it makes driving around in the woods much easier - backing up and moving around in tight spaces a lot easier. It does seem the assist levels vary for some reason - I don't know if it is a system voltage change with engine speed or something else - just not the consistent assist level you'll see in automotive applications.
It is a game changer with the Boss Plow on - MUCH easier to move around, although there still is inconsistency on the effort levels.
I was concerned there would be a significant drop in steering precision - this didn't happen - still feels good.
Long story short (too late I know!) - I am happy with the purchase and the performance of the system. Time will tell how robust the system is and if it performs this way in all conditions but I'm optimistic.
Hope this helps anybody out there considering the system!
I'll start by saying I'm in the auto industry and I evaluate steering systems and other things regularly. I will also say I am not a mechanic and borderline incompetent electronically. If you are a good mechanic and understand wiring/soldering, etc. you are well ahead of me and this may be a fairly simple exercise for you to install.
1.) Ordered system on a Sunday and received it on a Thursday - very happy with the response.
2.) Professional grade looking system - everything you need to install (except tools)
3.) Installation manual was straight forward mechanically, but to an electrical novice like me was very vague in the wiring instructions. This caused me a lot of angst, and ultimately some rework
4.) I've seen others have installed this in 3 hours - it took me most of three weekend days, but I took my time, learned how to solder from the internet, made multiple trips to an auto parts store (and Home Depot). I also will say I took my time and enjoyed the journey - I didn't have a deadline so I didn't rush - don't need extra stress!
5.) You will find the disassembly of the steering wheel and dash easier than it looks. My gator has the optional heater so it took a little longer, but no big deal
6.) First challenge encountered was getting my hands down to reach u-joint at steering rack - not a lot of room and a little tough to see. I ultimately found a path for the ratchet with a couple of extensions through a hole in the frame from the left side of the machine
7.) Second challenge was the snap rings on the upper shaft just below the steering wheel - there is an upper snap ring and a lower snap ring and they are much thicker than most snap rings. I bought a Channel Lock snap ring wrench on Amazon.com and it worked great on the upper snap ring. I then spent roughly 90 minutes on the lower snap ring, breaking the tips of the wrench and ultimately giving up and grinding off the snap ring after I thought I'd spent enough time on it (I considered cutting the whole shaft off with my Sawzall but finally got off the snap ring!). Could not proceed until I got this snap ring off because you must slide the shaft up to remove.
8.) Positioning the power steering unit was a bit challenging but not too bad - everything lined well with the frame.
9.) Had to sand off the paint on the upper shaft of the new unit to make it fit through the exisiting bearings on the frame.
10.) Total pain to try to tighten up the lower u-joint at the steering rack. You have to manage to hold one end of the bolt and reach through the aforementioned hole in the frame with a ratchet with extensions to tighten - trust me this will test your patience
11.) Once the unit was in went through the learning curve of understanding where to tie in to the existing wiring. You need battery power, a clean ground and switched ignition power. I grabbed the battery power from what I think is the fan relay in the front right of the machine. Picked up the ground from a bolt on the frame. Picked up the switched ignition power from the YELLOW wire off the ignition switch. (My biggest lesson learned is to check the power of each of these points before ever diassembling the machine - I tried to do it from a schematic and it is MUCH easier with a multimeter).
PERFORMANCE EVALUATION
I bought this system because 1.) the Boss snow plow makes the steering efforts very high and 2.) I want my wife to be able to use the machine and snow plow if I am gone. I evaluated the system first with the plow off, then with the plow on.
I am mostly happy with the system - it makes driving around in the woods much easier - backing up and moving around in tight spaces a lot easier. It does seem the assist levels vary for some reason - I don't know if it is a system voltage change with engine speed or something else - just not the consistent assist level you'll see in automotive applications.
It is a game changer with the Boss Plow on - MUCH easier to move around, although there still is inconsistency on the effort levels.
I was concerned there would be a significant drop in steering precision - this didn't happen - still feels good.
Long story short (too late I know!) - I am happy with the purchase and the performance of the system. Time will tell how robust the system is and if it performs this way in all conditions but I'm optimistic.
Hope this helps anybody out there considering the system!