PDA

View Full Version : Front drive shat Bad



ThomasM
04-11-2012, 08:22 PM
It finnally happen, front drive train sounds like a bucket of marbles. Took it to JD for the replacement under warrenty. Only had 80 hours on the machine. Hope the new one last longer and a lot less noise.

Deputy347k9
04-12-2012, 08:04 AM
I am assuming this is the long talked about problem with the shaft bearing? If this is it the new style will take care of the problem! My problem started slowly then progressed a bit. Now, runs like a DEERE should run!

Larry in ME

ncbowhnter
04-12-2012, 09:06 AM
mine is currently at the dealer getting checked out for the vibration noise under the cup holders/floorboard. 22 hours on it. figured I would take it in while still under the 1 year warranty. While I was there dropping it off I ordered the signal kit, horn kit, poly top and glass windshield with wiper. Which makes me believe that things happen for a reason.:Ysnd:

Skillet23
04-12-2012, 10:06 AM
Took mine in Tuesday for the driveshaft noise/vibration issue. Tech. there told me while it was in there for that there were a few other known issues that they would be taking care of.

Sorry, but I was in a hurry to do other things on my list and did not think about getting a list of the problems to post, but I'll correct that when I go to pick it up.

I know that one of the issues was that he said some machines have a known issue with a flaw in the machining of the rear end fluid cap. The cap will not seal properly, allowing oil to come out and water/dirt to go in. Might wanna check all your machines for this.

Will post other issues when pick up machine in a few days.

David in TX

Picked my Gator up the other day - they replaced drive-shaft and bearings - replaced rear end dipstick/fill cap (factory one had been cross threaded ONLY).

Regulator
04-12-2012, 04:05 PM
mine is currently at the dealer getting checked out for the vibration noise under the cup holders/floorboard. 22 hours on it. figured I would take it in while still under the 1 year warranty. While I was there dropping it off I ordered the signal kit, horn kit, poly top and glass windshield with wiper. Which makes me believe that things happen for a reason.:Ysnd:

You will be VERY happy with your purchases....I love my glass windshield with the wiper...couldn't live without it now that I have it...I have the signal kit too, but no horn kit...I have a mini-air horn that I will be installing soon...I bought it for a motorcycle a year or two ago and never used it, so it will go on the Gator...they are silly loud too!!!....I think the Deluxe, all glass cabs look a little better than the Poly Cab's, but I haven't regretted my decision to go with my Poly Cab...I have the sliding glass rear window too, and I love that as much as my windshield!!!....I think you will be tickled with your purchases!!!:Thmup:

Larry in MD :Jestr:

Charlie
04-12-2012, 05:29 PM
My 2011 825i had the same problem with front drive shaft noise right front day one ,took it to the J D dealer and they replace the shaft problem solve.

ThomasM
04-17-2012, 02:52 PM
Got my gator back today, no more rattle and vibration in front drive train. Runs and sounds like a Deere should now. The new front drive shaft makes one hell of a difference now, cant believe how quite it is. JD should have a recall on this problem, I believe that a lot a people don't know they have a problem and that the noise is normal. Shame on JD.

Deputy347k9
04-17-2012, 03:01 PM
ThonasNm I agree with you that John Deere should have a recall, however, it all comes down to dollar and cents. During the warranty periord we will replace any and all that complain. After the one years then they will have to pay the dealer for parts and labor. This adds more money for the dealer as well as John Deere. Now if the proble was to cause some sort of injury that may result in a law suit then I am sure they would have a total recall! The American way.

Larry in ME

ThomasM
04-17-2012, 05:29 PM
Yea thats the New American Way of doing business.

825joe
04-18-2012, 09:07 AM
After I had my new front shaft installed it was like a different machine. Very smooth!:Thmup:

Zephyr74
04-19-2012, 02:38 AM
Are they actually changing out the driveshaft or just the bearings?

pahawi
04-19-2012, 03:23 AM
From my dealer I ordered what was needed for solution# 87518 (drive shaft noise) and the only thing I got was one bearing. I replaced the front bearing with it and noise was gone.

Paul

825joe
04-19-2012, 08:59 AM
they replaced my whole assembly shaft and all.

Zephyr74
04-19-2012, 11:04 AM
they replaced my whole assembly shaft and all.

They replaced my bearing and ring/ pinon from my front differential. I had 7.6 hours on it. Took it out twice around my neighborhood and some other sounds are there in the front right wheel (sounds like a wheel bearing) and some new noise from the drive shaft area. So I have it back in the dealership right now with 8.5 hours on it. I called late yesterday and the lady said they ordered some parts for it but would call me today to tell me exactly what was wrong this time....I'll keep you updated.

825joe
04-19-2012, 11:27 AM
thanks bud

ThomasM
04-22-2012, 09:08 AM
Took a quick look and they changed shaft and bearings

Kiwi06
04-22-2012, 10:41 AM
Based on searching threads, JD made the switch to the new bearing right about the time my 825i was built. I haven't had any issues yet, but I'm concerned that I might have the old style bearing with issues awaiting me. How can I tell whether I have the new style or old style?

Thanks!

- Curious Steve in CO

pahawi
04-22-2012, 03:07 PM
How can I tell whether I have the new style or old style?

You can see the difference at the image in this thread:
http://www.johndeeregatorforum.com/forum/showthread.php?11991-Have-anyone-here-tried-to-replace-the-front-bearing-themselves&p=22228#post22228


Since it's the front bearing it's covered inside the tunnel, so you have to look in there. Maybe you can see it from the engine end, if you remove the rubber thingy. If not, try from the front end. In the front end you need to remove a metal cover to get access (one screw is holding it).

Paul

CaptDan
04-22-2012, 08:23 PM
Based on searching threads, JD made the switch to the new bearing right about the time my 825i was built. I haven't had any issues yet, but I'm concerned that I might have the old style bearing with issues awaiting me. How can I tell whether I have the new style or old style?

Thanks!

- Curious Steve in CO

when was yours built ?

Thanks

Dan - NJ

Kiwi06
04-23-2012, 09:29 AM
Hey Dan,

It's listed as Sept. 23, 2011. Another monkey wrench, though, is that it's possible that if it was built with the old style, it was swapped out already. I am the first "owner" but it was a John Deere demo/advertising unit prior to following me home.

- Steve in cool CO

Zephyr74
04-24-2012, 11:22 AM
I just talked to my dealer. A few months ago when I took my Gator in for the drive shaft noise they replaced the front drive shaft bearing and ring/ pinon in the front differential. This time they are replacing the pillow bearing between drive shafts.

Should they also be replacing the drive shaft itself?? It seems like everybody else has had the drive shaft also replaced but when I asked my dealer they said the solution number (that was posted on here) doesn't call for replacing the shaft and that the shaft is not causing the noise. Before I pick up my Gator, I want to make sure the drive shaft also doesn't need replacing. Any thoughts?

Also, they are replacing the front wheel bearing as they said it has a "hard spot" on it causing some noise as well. What is a "hard spot"? This machine only has 8.7 hours on it!

Thanks,
Zephyr74

pahawi
04-24-2012, 11:36 AM
Correct me if I'm wrong, but it's my understanding, only a few actually have had their drive shaft replaced. Most 825i's only get another style pillow bearing in the front. It beats me why some get a new drive shaft, so if anyone know why, please share your knowledge?

Thanks.

Paul

GATORDONE
04-24-2012, 05:16 PM
When the service bulliton first came out it called for replacing the driveshaft with the new bearing installed, They later revised the bulliton saying to just replace the rubber mounted pillow block bearing because they put the new pillow block in parts as a separate item.:Ysnd:

Zephyr74
04-24-2012, 08:08 PM
When the service bulliton first came out it called for replacing the driveshaft with the new bearing installed, They later revised the bulliton saying to just replace the rubber mounted pillow block bearing because they put the new pillow block in parts as a separate item.:Ysnd:

Thanks for the clarification!

ncbowhnter
04-24-2012, 08:28 PM
I called my dealer a couple of days ago to see if they could give me an estimate of when mine would be done. She told me that they had to order a new drive shaft for it and it should be in and fixed by the end of this week. Didn't ask why....just want it fixed.

jonny2guns4u
04-24-2012, 11:13 PM
When the service bulliton first came out it called for replacing the driveshaft with the new bearing installed, They later revised the bulliton saying to just replace the rubber mounted pillow block bearing because they put the new pillow block in parts as a separate item.:Ysnd:

Had mine in for the noise last week. They said they had replaced two bearings. Thank goodness I got the extended warranty. The repair didn't cost me a dime and it sounds and runs smoother.