PDA

View Full Version : About to order the Boss V Plow and hopefully a Prosum cab



hornadylnl
08-20-2012, 07:06 PM
I'm in the process of selling some stuff off and hope to have my order in for the Boss V plow by the end of the week. I've got one last thing to sell and hopefully will be ordering the full Prosum cab as well. I'll at least order the windshield and roof with the front lights and wiper. This will ensure that I don't get any snow this winter.

DIXIEDOG
08-20-2012, 07:37 PM
This will ensure that I don't get any snow this winter.


Guess we'll all owe you one :lol:


Judging from your user name is it safe to say you're into reloading a bit? I like my Hornady LNL AP press pretty dang well....it's a great piece of equipment.:Thmup:

hornadylnl
08-20-2012, 07:50 PM
I've got an lnl ap with case feeder. Got an 8 ball handle on it as well. :BG:

DIXIEDOG
08-20-2012, 09:25 PM
I've got an lnl ap with case feeder. Got an 8 ball handle on it as well. :BG:

The ultimate bling :lol:

hornadylnl
08-20-2012, 09:30 PM
I tried a dillon roller handle and hated it. The factory ball rubs your hand raw after awhile with the mold rib. The 8 ball is great.

DIXIEDOG
08-20-2012, 09:46 PM
I've left the factory round grip on mine and never had an issue....must have been lucky or haven't used it enough yet. I think they changed the design on the later ones a bit...mine is fairly old. Pre EZ Eject series....I put the EZ Eject plate on and modified all my shell plates to be EZ Eject ones. That was a nice improvement over the original design.

hornadylnl
08-20-2012, 09:53 PM
I got the new ez eject parts but I haven't gotten the shell plates yet.

DIXIEDOG
08-20-2012, 10:47 PM
I got the new ez eject parts but I haven't gotten the shell plates yet.

Do you have a mill? Or know somebody who works in a machine shop?



It took about 5 minutes per plate to fix them.....I tossed a 1/4" emill in and put the plates on a rotary table....bolt through the center so you can just loosen a nut slide that plate off....slip your next plate on and repeat. Hornady snags $10 a plate which isn't terrible but a buddy or you could do it for much cheaper....I expected the plates were going to be hardened but they cut like butter.

If you have a rotary table it could even be done on a small drill press.

hornadylnl
08-21-2012, 07:08 AM
I haven't used the press for awhile so I haven't done anything with it. I don't really have access to a mill.

hornadylnl
08-22-2012, 06:01 PM
I just sent out the check for the Boss V plow, smart hitch, shoes, and leg strap today. I'll get it some time after Labor Day (at my request. Not sure how soon I could get it otherwise). $3250 delivered is the best price I found. If anyone is interested, I got it through Red's Garage out of New York.

hornadylnl
08-23-2012, 05:28 PM
The dealer I bought my gator from is ordering me the following from Prosum.

Windshield kit
Roof kit
Header light kit
Wiper kit
Rear light kit
Dome light

Price before tax is $1292. I think that's about $25 markup from the prices I've seen posted here. I have to pay 7% sales tax on top of that but it's still cheaper than buying it direct and paying shipping. Plus, I'll be able to pick it up at my covenience instead of waiting on a freight delivery.

So if any of you guys are interested, you might see about going through your local Deere dealer to buy your Prosum stuff. I'm thinking this will help Prosum out as well. My dealer hasn't done any business with them and if he likes my stuff, he may recommend them to other gator buyers.

hornadylnl
08-28-2012, 06:47 PM
My Prosum stuff came into the dealer today. I'll pick it up after work tomorrow and see how much of it I can get installed tomorrow night. :BG:

hornadylnl
08-29-2012, 08:19 PM
I picked up my cab stuff at the dealer today. I got the roof, windshield, and lights all installed in about 2.5 hours. It was all pretty simple to install. The only issues I had were one of the windshield hinge bolts and the wiper arm. I could not get one of the hinge bolts to start and thought I had it going and it cross threaded. It snapped off when I tried to remove it. I was able to get it drilled out and retapped so I just need to get another flat head bolt. Also, I got the windshield wiper arm on and the angle was a little off. It was a bear to get back off so I'd suggest running the motor and watching where it stops. Makes some marks on it to figure out where the center is. When the wiper is in the center, the whole blade is on the glass but once it's up to the left and right, the top end of the blade goes off the glass. I don't know how much that will affect the ability of the blade to get a good wipe on the windshield.

Overall, I'm well pleased. I took it down the road to test the wind in my face with the windshield closed and open. I don't need near the blast in my face that I did without my windshield. I drove down a gravel road and not long after, I remembered other members talking about the dust coming in from behind the cab. Having the windshield open seemed to help some. I don't take my gator on the road that much so I don't think it will be much of an issue for me. I may buy a soft screen for the rear to cut down on the dust.

The lights seem to work pretty well. I closed my barn up to test them out. The front lights aim down and hit the ground between the gator and the factory headlights. The rear lights can be adjusted to just about anywhere you want them. I may see about replacing the bulbs with some silverstars or something whiter in the future. The wiring was slick and was mostly plug and play. I liked the fact that the front lights, switches, and motor were already installed and prewired. I only had to run the wire down the ops tube and to the battery compartment to hook up. For now, I have the wire zip tied to the ops tube. I may try to fish it through the ops tube in the future.

I'm well pleased with it and I recommend it. I will see how it does this winter and if it's too freaking cold, I'll probably break down and buy the door and rear panel kits. I'll take some pics tomorrow hopefully and post them. If you have any special areas you want detailed pics of, let me know and I'll try to get them for you.

hornadylnl
08-29-2012, 11:00 PM
Just took a quick night time drive. The lights are much better than I thought they were going to be. The front lights are perfect for lighting up the area between the gator and where the factory lights focus. The rear lights really light up the area behind the gator. You could definitely work out of the back end of your gator at night with these lights. The dome light is pretty decent as well. Now I just need a nice rain to test out the wiper. :BG:

hornadylnl
08-30-2012, 07:48 PM
Well, here are the pics I promised. Please forgive my dirty barn.

1384

1385

1386

1387

1388

hornadylnl
08-30-2012, 07:57 PM
I wondered what the protrusion was on the front of the roof and if it was open. Hopefully this pic will show it. I haven't seen any pics online of the rear lights and what they look like so here's a couple shots for you. If roof size is an issue, I don't think you'll find a more form fitting roof out there. I really sits right down on top of your OPS.

1389

1390

1391

1392

1393

hornadylnl
09-02-2012, 07:54 PM
We have a nice, steady light rain now. I just took it out and he wiper seemed to work well. I did have a mist start to build up on the inside of the windshield that was coming in from behind me. Does the rear window without doors keep the dust and mist from coming inside the cab area?

DIXIEDOG
09-02-2012, 07:55 PM
Nice looking set up :Thmup:

hornadylnl
09-11-2012, 06:36 PM
My Boss plow is supposed to be here Thursday. I'm going to take the day off work so hopefully I'll get it pretty early in the morning. I've already got the gator mostly prepped to start installing the mount. I downloaded the manuals off of Boss's website. I'm assuming they're the same ones that will come with the plow. They could definitely add some more pictures to better illustrate it. I don't know if I'll get it all done in a day or not but I'll try.

jdcellar
09-11-2012, 09:24 PM
That is a good looking set up you have. How much height does the roof add to the Gator?

hornadylnl
09-11-2012, 09:30 PM
I'd say 2" max and that would be up front. It really fits like a glove.

hornadylnl
09-13-2012, 08:51 PM
I got the plow delivered around 11 and got it done by 7. That includes taking time for lunch and dinner. I still have to adjust it yet. When I go to set it down in the V position, it sits on the outside shoes and then walks it's way down in the middle. I think I'm going to have to get some more washers or bushings for the shoes as there's still about an inch and a half between the washers and the lynch pins. When I pick the plow up, the shoes drop down.

I've got the front shocks on the stiffest setting and it drops the front end of the gator down pretty good. I think before I go trying to make adjustments to it, I'm going to go ahead and put about 500# in the bed.

1480

hornadylnl
09-14-2012, 10:19 PM
I got it adjusted better today. I put 4 mostly full buckets of wheel weights by the tail gate and that leveled it out pretty well. I adjusted the push arm to plow height and put the middle shoe on. I have the bushing and 3 washers in the middle shoe and the bushing and 5 washers on the outside shoes.