View Full Version : 855D skid plates
jcummins
12-07-2012, 04:10 PM
I thought the bottom was pretty well protected....I was wrong. The big issue is right in front of the rear differential. There is a wide opening that will catch any stick pointed in the wrong direction. There is tapped nuts there so something bolts up to protect that. I'm guessing aftermarket skid plates....OR am I missing a plate?
Like it had eyes, went into the fan belt behind the protective cover and popped the fan belt off. Overheated since no water pump. I'll be buying or building something for that? Anyone have the skid plates there?
Here's the stick poking from behind the cover.
http://i52.photobucket.com/albums/g27/jcummins42/Mobile%20Uploads/downsized_1206121004.jpg
The opening it came thru:
http://i52.photobucket.com/albums/g27/jcummins42/Mobile%20Uploads/downsized_1206121013.jpg
Opening from the side.
http://i52.photobucket.com/albums/g27/jcummins42/Mobile%20Uploads/downsized_1206121021.jpg
jakerator
12-07-2012, 05:31 PM
I wonder if the 825 is the same? Will have to do some nosing when I get a chance. It's way too "winter" right now, the gator is hibernating in the shed.
Destiny creek
12-08-2012, 12:59 PM
John Deere makes a plate for this plate for this opening called a deflector plate. I also ordered the full skid plate package and noticed the opening when a stick knocked off my purple starter wire and my new gator would not start.i went back to my dealer and he told me it was a separate accessory. I purchased the kit for around 50 dollars and takes about 15 minuntes to install
jcummins
12-08-2012, 02:58 PM
John Deere makes a plate for this plate for this opening called a deflector plate. I also ordered the full skid plate package and noticed the opening when a stick knocked off my purple starter wire and my new gator would not start.i went back to my dealer and he told me it was a separate accessory. I purchased the kit for around 50 dollars and takes about 15 minuntes to install
I found this... http://www.deere.com/wps/dcom/en_US/products/attachment/gator_attachments/protection/hd_skid_plate_extension_panel/hd_skid_plate_extension_panel.page
BUT, from the picture the focus of this picture is the larger plate....I got that. It's the plate that has slots in it that is partially off this picture. That slotted place would cover the opening the stick went through. Makes me think I'm missing part of the plate????
Others with 855D, do you have that opening? or do you have a plate there?
jdcellar
12-08-2012, 10:00 PM
I checked my 2012 855D today and it has the same opening on it.
Destiny creek
12-09-2012, 01:25 AM
The plate you are missing is the slotted one which is called the deflector plate which is not included in the skid plate package go figure.You can order it as a kit from the dealer for around 50 dollars.I don't understand why when a guy orders the skid plate package they don't include it or at least tell you it's not included.Also in the kit as reflector tape to cover the electrical wires on top of the Diesel engine due to the heat contained in the engine compartment because the opening is closed
jcummins
12-09-2012, 09:12 AM
The plate you are missing is the slotted one which is called the deflector plate which is not included in the skid plate package go figure.You can order it as a kit from the dealer for around 50 dollars.I don't understand why when a guy orders the skid plate package they don't include it or at least tell you it's not included.Also in the kit as reflector tape to cover the electrical wires on top of the Diesel engine due to the heat contained in the engine compartment because the opening is closed
Good gosh.....to me there is no engine compartment...it's very open on the sides. If that opening is there because of heat, some kind of ram air ducting is needed.
Destiny creek
12-09-2012, 01:53 PM
Good gosh.....to me there is no engine compartment...it's very open on the sides. If that opening is there because of heat, some kind of ram air ducting is needed.
Be what it may but that is the explanation right from John Deere and I am sure they have researched it to worse case scenario
jcummins
12-09-2012, 02:30 PM
Be what it may but that is the explanation right from John Deere and I am sure they have researched it to worse case scenario
Agreed...BUT...the marketing department trumps the engineering. I like my 855D but I see things that are doing solely for cost reasons. This is probably one of them.
ratrod
12-09-2012, 04:42 PM
maybe its just the 855d but I'm pretty sure that my 825i came with that part of the skid plate from the factory.
jcummins
12-09-2012, 05:46 PM
maybe its just the 855d but I'm pretty sure that my 825i came with that part of the skid plate from the factory.
You just made my point...just like the lack of instrumentation.
ratrod
12-09-2012, 06:59 PM
You just made my point...just like the lack of instrumentation.
What does the 855d lack in instrumentation?
jcummins
12-09-2012, 08:15 PM
What does the 855d lack in instrumentation?
Just idiot lights. No tach, no speedo. Actually don't need either, but I'd like an voltmeter, oil pressure, and temp... gauges, not lights. I'm speculating the diesel motor cost them more so they cut some corners, and dropped the instrument cluster the 825i has.
Deputy347k9
12-09-2012, 08:44 PM
To simplify the matter would someone that does have all the plates post a picture either installed or not.
Larry in NC
Destiny creek
12-10-2012, 01:58 AM
To simplify the matter would someone that does have all the plates post a picture either installed or not.
Larry in NC
http://viewer.zmags.com/publication/042e40e2#/042e40e2/12
This is the link for protection packages offered by JD
Destiny creek
01-01-2013, 01:42 PM
:Seya:
Powered by vBulletin® Version 4.2.2 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.