View Full Version : Wiring the John Deere way
Bunky
10-12-2013, 08:24 AM
I am planning on adding some accessories and want to wire the JD way which seems to having one basic connection to main harness but when adding a new accessory yoiu add a "daisy" power connector (use the existing one, create a second one).
In looking in the front area, I see several unused connectors and looking around the battery the mid range light kit and the windshield wiper added several more. I notice two primary wiring colors (red / black, yellow / black) but have not had a chance to determine if one is hot and other is switched. The yellow/black look like they could be low power accessory and the red/black always look like higher current carrying wiring.
I also would like to use a connector to tap into the harness so wanted to now if anyone knows what the connectors used are. The taps look mostly like a T-shaped connector. It would be great of JD just sold a wiring harness adapter.
Available connectors in front section:
http://angphoto.smugmug.com/Detailing/ANG-Gallery/i-NP2xwkt/0/X3/ANG_1960-1-X3.jpg
http://angphoto.smugmug.com/Detailing/ANG-Gallery/i-xK27Cbb/0/X3/ANG_1959-1-X3.jpg
http://angphoto.smugmug.com/Detailing/ANG-Gallery/i-LbTw46g/0/X3/ANG_1954-1-X3.jpg
jradue
10-12-2013, 10:55 PM
The connectors are all Delphi 56 series for most of the connectors. A couple are different, like the fuel pump connector. Go to the electricaldepot.com and they have all you need, and they are cheaper than getting them from the dealer. I have bought tons of them. You will need the connectors, and companion terminals. The sell a very expensive tool to crimp the terminals, but a needlenose pliers works fine.
Bunky
10-13-2013, 08:04 AM
Thanks.
I found this on ebay that seems to have some of the connectors I have seen -- just a mere $130...
http://ecx.images-amazon.com/images/I/91EoccKRQsL._SL1500_.jpg
jradue
10-13-2013, 10:41 AM
Thanks.
I found this on ebay that seems to have some of the connectors I have seen -- just a mere $130...
http://ecx.images-amazon.com/images/I/91EoccKRQsL._SL1500_.jpg
You can get them a lot cheaper than that. See here: http://theelectricaldepot.com/index.php?main_page=index&cPath=7_220&zenid=92ad7b25c0565f810e4faa84be3c7360
Catchad81
01-13-2014, 10:13 PM
Question: I have installed a EZ Steer power steering unit that uses that uses the main power harness under the dash. I know what to install the Long Range light kit that connects to the same main power harness. Neither added wiring harness extends the existing power wires for additional connections. What is the best way to connect both accessories and possibly more?
Thanks.
I am planning on adding some accessories and want to wire the JD way which seems to having one basic connection to main harness but when adding a new accessory yoiu add a "daisy" power connector (use the existing one, create a second one).
In looking in the front area, I see several unused connectors and looking around the battery the mid range light kit and the windshield wiper added several more. I notice two primary wiring colors (red / black, yellow / black) but have not had a chance to determine if one is hot and other is switched. The yellow/black look like they could be low power accessory and the red/black always look like higher current carrying wiring.
I also would like to use a connector to tap into the harness so wanted to now if anyone knows what the connectors used are. The taps look mostly like a T-shaped connector. It would be great of JD just sold a wiring harness adapter.
Available connectors in front section:
http://angphoto.smugmug.com/Detailing/ANG-Gallery/i-NP2xwkt/0/X3/ANG_1960-1-X3.jpg
http://angphoto.smugmug.com/Detailing/ANG-Gallery/i-xK27Cbb/0/X3/ANG_1959-1-X3.jpg
http://angphoto.smugmug.com/Detailing/ANG-Gallery/i-LbTw46g/0/X3/ANG_1954-1-X3.jpg
Bunky
01-14-2014, 09:29 AM
I created a daisy chain setup so something similar would need to be done: 1 for ez steer, 1 for lights. The long range kit should do something similar in creating a second connection. I do not have my tech manual handy but JD has power steering too so there must be a connection / method to do both (JD PS and light kit).
Catchad81
01-14-2014, 09:01 PM
You're right, it daisy chains in the light harness. Guess I wasn't paying enough attention to what I was working up yesterday!
I created a daisy chain setup so something similar would need to be done: 1 for ez steer, 1 for lights. The long range kit should do something similar in creating a second connection. I do not have my tech manual handy but JD has power steering too so there must be a connection / method to do both (JD PS and light kit).
Bunky
01-15-2014, 08:42 AM
Good to hear.
I looked at my tech ref manual for an 825i and from what I can tell (do not have PS or EPAS as JD calls it to confirm or near my Gator), the unswitched power and ground for the EPAS are in separate single line connectors. I see a separate red and black wire in the schematic.
It does not hook into the front power port. The switch power appears to be included in a multi-wire connector and not through the black/yellow dual connector.
bradhill
11-30-2015, 01:29 AM
Sent from my iPhone using my index finger
Powered by vBulletin® Version 4.2.2 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.