did you install an extra battery for the bed winch or run power from the factory battery, i made a plate and welded a hitch receiver tube to it for a rear winch , but havend quite figured how i want...
Type: Posts; User: campoman
did you install an extra battery for the bed winch or run power from the factory battery, i made a plate and welded a hitch receiver tube to it for a rear winch , but havend quite figured how i want...
i was curious about the interfearance between valves and pistons , i contacted a john deer rep and he assured me that the cherry 3 cyl engine was not an interfearance engine so i havent been to...
i would look at the pedal control to see if the previous owner crossed some wires to bypass intermediate speeds, might be all it would take, if possible i would try and contact the previous owner and...
dont know when you sent this reply but thanks my starter has been acting up and ive been puttingh it off because it looked like a real chore good to hear that its not bad to replace did you pull the...
I have a 2014 825i gator,havent had many issues with it except for fuel pump and parking brake ,still don't understand how members are saying adding oil to this unit will take up on adj .seems you...
can anyone tell me how adding oil to the parking brake assy can compensate for a parking brake that wont hold i have read from numerous members that they had added oil and now parking brake holds i...
very good description of how to do this job , this is a very cheap starter ,im trying to find out if anyone makes a upgrade for this starter
don't buy the cheap 25 to 30.oo disc pads they squeak so bad you could never use the gator for hunting
does anyone know if they make a starter upgrade for a 825i gas engine ,from what I hear the factory starter is a real cheap assy and a lot of work to replace , im not ready to do that yet but hope...
could still be a ground issue, do you have power to the starter ?I worked on one the other day that a rat had chewed through a number of wires . if not the issue clean and check all your grounds
did you check to see that you have power from the temp sensor to the Elec fan once it gets past normal operating temp?
my 825 did the same thing after doing some electrical work on it it turned out to be a connection on one of the fuses in fact it did it twice I replaced most of the fuses related to ignition mhope...
I believe most of those wires are 14 gauge
looking for a spare alloy 14 inch 5 lug wheel for 825 gator
sounds to reason that if you didn't have the noise before it wouldn't be a valve clatter noise all of a sudden I know a faulty injector can make a taping or knocking noise other then that carbon...
I have replaced 2 ignition switches I'm not familiar with your model but I would checkon my 825 on. e came from amazon , piece of junk so I bought a factory switch , have had no further problem, as...
if you are dealing with a high swr reading make sure that the antennae bracket has a good clean area where the antennae adapter screws down to the bracket if that still dosnt solve the problem put a...
I have the same noise its the starter drive the shaft gets dry and causes it to make that squaling noise im not going to worry to much about it , I have a feeling when the weather warms up you wont...
I had recently looked for info on how to adjust the parking brake on a 825 gator , had a lot of members giving info on how to repair , which didn't help me much I finally decided I was just going to...
nice outfit, I figure if we stay in the back country we won't need a mask , just maybe a fishing pole and a beer
looking for a alloy or steel wheel for 9 inch wide 14 inch wheel for an 825 gator
does anyone know if any aftermarket supplies any gear ratio change for gators
hi jeff don't remember if I had answered you about the muffler I still have it available dropped price to 65.00 plus shipping if you might still be interested Al
recently changed tire size on my 825 went from stock 27x14 to 28x14 , had very little diference in acceleration or power , did give me more ground clearance which I was after very happy with this...
finally was able to get ahold of a john deere tech with question about engine interference the 825 3 cyl and he assured be it was not an interference engine so no worry about destroying the engine...